Members: 0 member(s)

Shares ?

0

Clicks ?

0

Viral Lift ?

0%

Other 1,010 views Oct 08, 2018
Injection Molding Of Thin-Walled Pet Bottle Mould

From the level of Pet Bottle Preform operation, the injection and holding pressure are the same.
1. In addition to the use of the injection servo valve, the injection directional valve is opened during injection and pressure holding, which does not close (of course does not rotate).
2. On the computer screen, control the injection pressure and pressure.
3, the splitting of the injection, although the position of the screw is the most accurate, but can also be used to distinguish the time (called time injection), the same as the same section.
Therefore, some operators do not use the pressure section and the injection section or a few sections of pressure to do the pressure.
Note: For example, the injection time of three and four injections limits the injection (extrusion) to only the injection time, but not the more precise injection position.
The computer injection molding machine will have the following two functions:
1. In the position + time mode, you can specify the injection time limit. The injection time to the upper limit of the screw has not yet reached the pressure point, and the process will continue to maintain pressure. This is a flow channel blockage in a multi-cavity injection cavity. When the pressure is not in use, it cannot use this mode, only time injection
2. The pressure points before and after the two areas are outside, the screw is not in the proper position, called the smaller area, and the screw has a pressure point called the overflow area. Both have the opportunity to generate waste and notify the operator to deal with it. Do not use pressure segments not on this feature.
If the computer can provide a linearly decreasing pressure, do not use this feature and you cannot use it. Closed loop control for precision thin walled Pet Bottle Mould injection molding. The closed loop control only allows injection speed control, the upper pressure limit of the pressure control section, and the pressure control section is used to control the pressure. 



preform nicole 's Entries

30 blogs
  • 10 Oct 2018
    Injection Molding Plastics Since the introduction of the injection molding process for the first time in the 1930s, the advantages of injection molding over die casting have been controversial. This approach has both benefits and limitations, mainly based on requirements. pet preform manufacturers and other consumers who rely on molded parts to produce products are looking for factors such as quality, durability and economy to determine which molded parts are best suited to their needs.What is injection molding?Injection molding is a method of manufacturing a finished part or product by pressing a molten plastic into a mold and hardening it. The use of these components is as extensive as the various products produced by the process. Depending on the application, injection molded parts can range in weight from a few ounces to hundreds or thousands of pounds. In other words, from computer parts, soda bottles and toys to trucks, tractors and car parts.Injection drawingPlastic injection molding and die castingThe injection molding process was originally modeled by die casting, a similar process in which molten metal is pressed into a mold to produce parts for making the product. However, die casting mainly uses non-ferrous metals such as zinc, aluminum, magnesium and brass instead of using plastic resins to produce parts. Although almost any part can be cast from any metal, aluminum has developed into one of the most popular metals. It has a low melting point which makes it easy to form parts. The mold is stronger than the mold used in the permanent mold process and can withstand high pressure injections of 30,000 psi or higher. The high pressure process produces a durable, fine grade structure with fatigue strength. Because of this, die casting is used from engine and engine parts to pots and pans.Die casting benefitIf your company needs rugged, durable, mass-produced metal parts such as junction boxes, pistons, cylinder heads and engine blocks, or propellers, gears, bushings, pumps and valves, die casting is the ideal choice.StronglastingEasy to mass produceDie casting limitHowever, it can be said that although die casting has its advantages, there are some limitations in this method that need to be considered.Limited part sizes (up to approximately 24 inches and 75 pounds.)High initial processing costMetal prices will fluctuate significantlyWaste increases production costsInjection molding benefitsFor many years, the benefits of preform injection molding of Pet Bottle Preform have become more popular because of their advantages over traditional die-casting methods. That is to say, the number and variety of low-cost, inexpensive products made today from plastic are almost limitless. There are also minimum finishing requirements. 
    3778 Posted by preform nicole
  • Injection Molding Plastics Since the introduction of the injection molding process for the first time in the 1930s, the advantages of injection molding over die casting have been controversial. This approach has both benefits and limitations, mainly based on requirements. pet preform manufacturers and other consumers who rely on molded parts to produce products are looking for factors such as quality, durability and economy to determine which molded parts are best suited to their needs.What is injection molding?Injection molding is a method of manufacturing a finished part or product by pressing a molten plastic into a mold and hardening it. The use of these components is as extensive as the various products produced by the process. Depending on the application, injection molded parts can range in weight from a few ounces to hundreds or thousands of pounds. In other words, from computer parts, soda bottles and toys to trucks, tractors and car parts.Injection drawingPlastic injection molding and die castingThe injection molding process was originally modeled by die casting, a similar process in which molten metal is pressed into a mold to produce parts for making the product. However, die casting mainly uses non-ferrous metals such as zinc, aluminum, magnesium and brass instead of using plastic resins to produce parts. Although almost any part can be cast from any metal, aluminum has developed into one of the most popular metals. It has a low melting point which makes it easy to form parts. The mold is stronger than the mold used in the permanent mold process and can withstand high pressure injections of 30,000 psi or higher. The high pressure process produces a durable, fine grade structure with fatigue strength. Because of this, die casting is used from engine and engine parts to pots and pans.Die casting benefitIf your company needs rugged, durable, mass-produced metal parts such as junction boxes, pistons, cylinder heads and engine blocks, or propellers, gears, bushings, pumps and valves, die casting is the ideal choice.StronglastingEasy to mass produceDie casting limitHowever, it can be said that although die casting has its advantages, there are some limitations in this method that need to be considered.Limited part sizes (up to approximately 24 inches and 75 pounds.)High initial processing costMetal prices will fluctuate significantlyWaste increases production costsInjection molding benefitsFor many years, the benefits of preform injection molding of Pet Bottle Preform have become more popular because of their advantages over traditional die-casting methods. That is to say, the number and variety of low-cost, inexpensive products made today from plastic are almost limitless. There are also minimum finishing requirements. 
    Oct 10, 2018 3778
  • 09 Oct 2018
    In the field of product development and manufacturing, 3D printing and injection molding are almost universally considered to be among the best available methods. While these methods are versatile and well suited for many situations and uses, they vary widely in several ways: method, material, volume, cost, and best application – just a 5-gallon Pet Preform example.confrontationAs an entrepreneur, new product developer or engineer, you probably know that 3D printing and injection molding are definitely two options you should research and pursue to create your product or prototype and understand some of the key differences between the two. Very important. First, they operate in a completely different way. Let us briefly outline what this means.Injection molding and 3D printing: What are they?Injection molding involves injecting a heated liquefied plastic material into a mold that contains a 3D "negative film" that can be thought of as your part: when the liquefied plastic fills the mold cavity, it forms and forms your part. . Once the mold cavity is filled, the substrate is allowed to cool and resolidify and then drained from the mold for inspection and dispensing.Injection molding machines cost hundreds of thousands of dollars to facilitate the entire cycle: material loading, injection, cooling and parts removal. Injection molds are almost always custom made of steel, aluminum or other metals to fit the specifications of a particular part, and they are split into two halves so they can be pushed out separately. In addition to the cavity having the "negative" shape of the part, the mold also contains a hollow area called a "flow path" for conveying the molten material into the cavity.The 3D printing process works much differently than injection molding. The size, shape, and other physical characteristics of the product are loaded into the 3D printer through CAD drawings or other compatible files, rather than forming the part through a preformed mold. The machine then builds parts from the ground and processes the thin lines of plastic substrates that are transported through the machine.If you don't know how to choose the right craftsmanship for your mold, please contact Jilian Plastics. We are a well-experienced china pet preform manufacturers that can find the right method for you.
    1251 Posted by preform nicole
  • In the field of product development and manufacturing, 3D printing and injection molding are almost universally considered to be among the best available methods. While these methods are versatile and well suited for many situations and uses, they vary widely in several ways: method, material, volume, cost, and best application – just a 5-gallon Pet Preform example.confrontationAs an entrepreneur, new product developer or engineer, you probably know that 3D printing and injection molding are definitely two options you should research and pursue to create your product or prototype and understand some of the key differences between the two. Very important. First, they operate in a completely different way. Let us briefly outline what this means.Injection molding and 3D printing: What are they?Injection molding involves injecting a heated liquefied plastic material into a mold that contains a 3D "negative film" that can be thought of as your part: when the liquefied plastic fills the mold cavity, it forms and forms your part. . Once the mold cavity is filled, the substrate is allowed to cool and resolidify and then drained from the mold for inspection and dispensing.Injection molding machines cost hundreds of thousands of dollars to facilitate the entire cycle: material loading, injection, cooling and parts removal. Injection molds are almost always custom made of steel, aluminum or other metals to fit the specifications of a particular part, and they are split into two halves so they can be pushed out separately. In addition to the cavity having the "negative" shape of the part, the mold also contains a hollow area called a "flow path" for conveying the molten material into the cavity.The 3D printing process works much differently than injection molding. The size, shape, and other physical characteristics of the product are loaded into the 3D printer through CAD drawings or other compatible files, rather than forming the part through a preformed mold. The machine then builds parts from the ground and processes the thin lines of plastic substrates that are transported through the machine.If you don't know how to choose the right craftsmanship for your mold, please contact Jilian Plastics. We are a well-experienced china pet preform manufacturers that can find the right method for you.
    Oct 09, 2018 1251
  • 08 Oct 2018
    From the level of Pet Bottle Preform operation, the injection and holding pressure are the same.1. In addition to the use of the injection servo valve, the injection directional valve is opened during injection and pressure holding, which does not close (of course does not rotate).2. On the computer screen, control the injection pressure and pressure.3, the splitting of the injection, although the position of the screw is the most accurate, but can also be used to distinguish the time (called time injection), the same as the same section.Therefore, some operators do not use the pressure section and the injection section or a few sections of pressure to do the pressure.Note: For example, the injection time of three and four injections limits the injection (extrusion) to only the injection time, but not the more precise injection position.The computer injection molding machine will have the following two functions:1. In the position + time mode, you can specify the injection time limit. The injection time to the upper limit of the screw has not yet reached the pressure point, and the process will continue to maintain pressure. This is a flow channel blockage in a multi-cavity injection cavity. When the pressure is not in use, it cannot use this mode, only time injection2. The pressure points before and after the two areas are outside, the screw is not in the proper position, called the smaller area, and the screw has a pressure point called the overflow area. Both have the opportunity to generate waste and notify the operator to deal with it. Do not use pressure segments not on this feature.If the computer can provide a linearly decreasing pressure, do not use this feature and you cannot use it. Closed loop control for precision thin walled Pet Bottle Mould injection molding. The closed loop control only allows injection speed control, the upper pressure limit of the pressure control section, and the pressure control section is used to control the pressure. 
    1011 Posted by preform nicole
  • From the level of Pet Bottle Preform operation, the injection and holding pressure are the same.1. In addition to the use of the injection servo valve, the injection directional valve is opened during injection and pressure holding, which does not close (of course does not rotate).2. On the computer screen, control the injection pressure and pressure.3, the splitting of the injection, although the position of the screw is the most accurate, but can also be used to distinguish the time (called time injection), the same as the same section.Therefore, some operators do not use the pressure section and the injection section or a few sections of pressure to do the pressure.Note: For example, the injection time of three and four injections limits the injection (extrusion) to only the injection time, but not the more precise injection position.The computer injection molding machine will have the following two functions:1. In the position + time mode, you can specify the injection time limit. The injection time to the upper limit of the screw has not yet reached the pressure point, and the process will continue to maintain pressure. This is a flow channel blockage in a multi-cavity injection cavity. When the pressure is not in use, it cannot use this mode, only time injection2. The pressure points before and after the two areas are outside, the screw is not in the proper position, called the smaller area, and the screw has a pressure point called the overflow area. Both have the opportunity to generate waste and notify the operator to deal with it. Do not use pressure segments not on this feature.If the computer can provide a linearly decreasing pressure, do not use this feature and you cannot use it. Closed loop control for precision thin walled Pet Bottle Mould injection molding. The closed loop control only allows injection speed control, the upper pressure limit of the pressure control section, and the pressure control section is used to control the pressure. 
    Oct 08, 2018 1011
  • 07 Oct 2018
    The Pet Bottle Mould blowing machine is a kind of mechanical, electronic control, hydraulic integrated crystallization, electrical complexity, oil pipeline crossing the building, various fault phenomena are controllers, all kinds of strange things, different. Large PET bottle blowing machines have only tens of thousands of parts. If one of the parts fails, the PET bottle blowing machine will be abnormal, and the wire connection will cause problems if it is slightly inadvertent, plus the blower is bulky. PET, without the impact of a constant temperature blow molding machine on the shop environment, can easily lead to failure. To this end, the maintenance problems of imported PET blow molding machines are in front of us.How to quickly identify faults, hidden dangers and timely elimination? I think we should have a high sense of responsibility. Secondly, we should try our best to master the numerical control hydraulic technology. The practice of maintaining the blow molding machine for many years makes the PET more and more want to look more and more, and the more we want to practice, gradually improve our technical level and maintenance ability. , able to adapt to a variety of complex situations, solve difficult problems, PET bottle blowing machine.1View more PET blower electronic circuit informationWant to know more, understand the characteristics and functions of various PET blow molding machines, electronic circuit systems and PC PLC PLC; understand the electronic alarm system and troubleshooting of PET blow molding machine; understand the meaning of setting parameters of PC and PLCPET blow molding machine; Understand the programming language of PC and PLC; understand the method of programming PET blow molding machine; to understand the operation of the control panel PET blow molding machine and the contents of the menu, how long does it take to have a lot of data? I think the main focus, to clarify the sequence of events, is to master the spirit of the PET blow molding machine controller structure and control block diagram. The rest can be "visiting" and reading, but the content of each part must emphasize understanding and mastery. Because the internal circuit diagram of the PET blower controller is quite complicated, the manufacturer does not provide it. So you don't have to think about it in detail. Pay attention to the role of each part, the function of the board, the position of the interface, the meaning of the LED light, etc.. Now the model of the PET blow molding machine is updated fast, different manufacturers and different models are often different. Understand its commonality and personality.2View more PET blow molding machine electrical diagram, digest PET blower electrical diagramFor each electrical component, such as contactors, relays, time relays, and PC, PLC inputs, outputs, be marked on the electrical diagram.3. View more PET blow molding machine hydraulic drawings and digest them deeplyFor PET blow molding machines, hydraulic diagrams to understand their function and sequence of events. And one by one on the drawing, such as the lock mode is made by which solenoid valve action? Corresponding to PC, PLC output, what are the inputs? As shown in the figure, so from the electromechanical action to the extreme, at the same time, especially for the motor, more closely related to the understanding, now PET blow molding machine using electro-hydraulic proportional technology, should pay attention to understanding the role and function, especially understanding Adjustment methods and adjustment data, current pressure proportional valve pumps and corresponding static and dynamic, can understand and understand the motor, mechatronics, master various skills, such as the ability to solve problems.china pet preform manufacturers have a wealth of experience in pet blow molding machines, can quickly help you identify machine failures, eliminate problems, ensure that you smoothly produce products, and minimize losses.
    773 Posted by preform nicole
  • The Pet Bottle Mould blowing machine is a kind of mechanical, electronic control, hydraulic integrated crystallization, electrical complexity, oil pipeline crossing the building, various fault phenomena are controllers, all kinds of strange things, different. Large PET bottle blowing machines have only tens of thousands of parts. If one of the parts fails, the PET bottle blowing machine will be abnormal, and the wire connection will cause problems if it is slightly inadvertent, plus the blower is bulky. PET, without the impact of a constant temperature blow molding machine on the shop environment, can easily lead to failure. To this end, the maintenance problems of imported PET blow molding machines are in front of us.How to quickly identify faults, hidden dangers and timely elimination? I think we should have a high sense of responsibility. Secondly, we should try our best to master the numerical control hydraulic technology. The practice of maintaining the blow molding machine for many years makes the PET more and more want to look more and more, and the more we want to practice, gradually improve our technical level and maintenance ability. , able to adapt to a variety of complex situations, solve difficult problems, PET bottle blowing machine.1View more PET blower electronic circuit informationWant to know more, understand the characteristics and functions of various PET blow molding machines, electronic circuit systems and PC PLC PLC; understand the electronic alarm system and troubleshooting of PET blow molding machine; understand the meaning of setting parameters of PC and PLCPET blow molding machine; Understand the programming language of PC and PLC; understand the method of programming PET blow molding machine; to understand the operation of the control panel PET blow molding machine and the contents of the menu, how long does it take to have a lot of data? I think the main focus, to clarify the sequence of events, is to master the spirit of the PET blow molding machine controller structure and control block diagram. The rest can be "visiting" and reading, but the content of each part must emphasize understanding and mastery. Because the internal circuit diagram of the PET blower controller is quite complicated, the manufacturer does not provide it. So you don't have to think about it in detail. Pay attention to the role of each part, the function of the board, the position of the interface, the meaning of the LED light, etc.. Now the model of the PET blow molding machine is updated fast, different manufacturers and different models are often different. Understand its commonality and personality.2View more PET blow molding machine electrical diagram, digest PET blower electrical diagramFor each electrical component, such as contactors, relays, time relays, and PC, PLC inputs, outputs, be marked on the electrical diagram.3. View more PET blow molding machine hydraulic drawings and digest them deeplyFor PET blow molding machines, hydraulic diagrams to understand their function and sequence of events. And one by one on the drawing, such as the lock mode is made by which solenoid valve action? Corresponding to PC, PLC output, what are the inputs? As shown in the figure, so from the electromechanical action to the extreme, at the same time, especially for the motor, more closely related to the understanding, now PET blow molding machine using electro-hydraulic proportional technology, should pay attention to understanding the role and function, especially understanding Adjustment methods and adjustment data, current pressure proportional valve pumps and corresponding static and dynamic, can understand and understand the motor, mechatronics, master various skills, such as the ability to solve problems.china pet preform manufacturers have a wealth of experience in pet blow molding machines, can quickly help you identify machine failures, eliminate problems, ensure that you smoothly produce products, and minimize losses.
    Oct 07, 2018 773
  • 29 Sep 2018
    Estimate the cooling time of Pet Preform Mould injection moldingFortunately, the cooling time can be reasonably accurately estimated using an equation and a number called the "effective thermal diffusivity", which depends to a large extent on the thickness of the part. “The thermal diffusivity is a measure of how heat enters and exits a given material. In addition, when considering the thickness of a part, it constitutes most of the measure of cooling time.The thermal diffusivity can be calculated by dividing the thermal conductivity of the part by its density multiplied by the product of the specific heat (the energy required to increase the temperature by 1 degree). Each of these values ​​can be found on the specification sheet for the material used, or contact the manufacturer. Because cooling time is so important, it's best to get this data from first-hand sources (not third-party websites).Once you know the thermal diffusivity of the part, you can insert it into the rest of the cooling time equation. First, divide the square of the part thickness by the product: the square of the thermal diffusivity multiplied by 6.28 (or twice the "pi"). Then multiply this number by the logarithmic equation. If you are not an engineer, it may be time to call your engineer.For the person of interest, the calculated initial quantity is multiplied by the logarithmic function of the melt temperature minus the mold temperature (the material maintains the optimum temperature of the mold profile); divided by the mold release temperature minus the mold temperature; multiplied by four Divide by "π". “Fortunately, there are many calculators on the web that can help you with this equation. Of course, any valuable injection molding partner should be proficient in these numbers.The importance of the mold in the cooling timeAs can be seen from the above, mold cooling plays an important role in the injection molding cooling time. Mold design is also an important factor: cooling channels can and should be designed into the mold as much as possible to help more efficient heat dissipation. When you consider the heat path during cooling, the importance of efficiently cooling the mold from material to mold to the surrounding environment is easy to explain. Effective mold cooling means effective overall cooling.What happens when the injection molding is not enough?When the injection molding cooling time is improper or insufficient, the biggest problem you will encounter is defective and unqualified parts. The most common cases are those parts that have not yet been cured enough to retain their shape, which are subsequently damaged by the launch of the ram. Improper or inefficient cooling – including poor mold design – can also lead to part errors such as warpage, shrinkage, sinking, etc. Consistent, well-designed cooling times are one of the biggest steps to improve the quality of finished products and reduce the number of defects.Another factor to keep in mind is that proper cooling temperature does not mean reaching room temperature, nor does it mean that it is cold to the touch. The part should only be cooled to the extent that it retains its shape and can be safely pushed out of the mold. Any further cooling is ineffective (or almost ineffective) and will only unnecessarily lengthen the cycle time.Ultimately, mathematically estimating the appropriate cooling time for China Pet Bottle will help to avoid excessive cooling and deficiencies.
    611 Posted by preform nicole
  • Estimate the cooling time of Pet Preform Mould injection moldingFortunately, the cooling time can be reasonably accurately estimated using an equation and a number called the "effective thermal diffusivity", which depends to a large extent on the thickness of the part. “The thermal diffusivity is a measure of how heat enters and exits a given material. In addition, when considering the thickness of a part, it constitutes most of the measure of cooling time.The thermal diffusivity can be calculated by dividing the thermal conductivity of the part by its density multiplied by the product of the specific heat (the energy required to increase the temperature by 1 degree). Each of these values ​​can be found on the specification sheet for the material used, or contact the manufacturer. Because cooling time is so important, it's best to get this data from first-hand sources (not third-party websites).Once you know the thermal diffusivity of the part, you can insert it into the rest of the cooling time equation. First, divide the square of the part thickness by the product: the square of the thermal diffusivity multiplied by 6.28 (or twice the "pi"). Then multiply this number by the logarithmic equation. If you are not an engineer, it may be time to call your engineer.For the person of interest, the calculated initial quantity is multiplied by the logarithmic function of the melt temperature minus the mold temperature (the material maintains the optimum temperature of the mold profile); divided by the mold release temperature minus the mold temperature; multiplied by four Divide by "π". “Fortunately, there are many calculators on the web that can help you with this equation. Of course, any valuable injection molding partner should be proficient in these numbers.The importance of the mold in the cooling timeAs can be seen from the above, mold cooling plays an important role in the injection molding cooling time. Mold design is also an important factor: cooling channels can and should be designed into the mold as much as possible to help more efficient heat dissipation. When you consider the heat path during cooling, the importance of efficiently cooling the mold from material to mold to the surrounding environment is easy to explain. Effective mold cooling means effective overall cooling.What happens when the injection molding is not enough?When the injection molding cooling time is improper or insufficient, the biggest problem you will encounter is defective and unqualified parts. The most common cases are those parts that have not yet been cured enough to retain their shape, which are subsequently damaged by the launch of the ram. Improper or inefficient cooling – including poor mold design – can also lead to part errors such as warpage, shrinkage, sinking, etc. Consistent, well-designed cooling times are one of the biggest steps to improve the quality of finished products and reduce the number of defects.Another factor to keep in mind is that proper cooling temperature does not mean reaching room temperature, nor does it mean that it is cold to the touch. The part should only be cooled to the extent that it retains its shape and can be safely pushed out of the mold. Any further cooling is ineffective (or almost ineffective) and will only unnecessarily lengthen the cycle time.Ultimately, mathematically estimating the appropriate cooling time for China Pet Bottle will help to avoid excessive cooling and deficiencies.
    Sep 29, 2018 611
  • 28 Sep 2018
    Your choice of china pet preform manufacturers will determine your success or failure. Speaking of your product, there should be no omissions. You need to ensure the quality of each step. Choosing the right manufacturer of custom plastic parts is the only way.Here are a few questions you should ask when choosing a suitable plastic parts manufacturer:Are their quality management system certified?The manufacturer's quality management system (QMS) determines their output. Certain industry standards should be adhered to to meet each product requirement. Make sure they pass the ISO certification. In addition, ensure that the certifying party is recognized and impartial.Is there enough support for new product development?A competent engineering support team can ensure the efficiency of each step. It is this team that can help Pet Bottle Mould balance design and manufacturing optimization. In this way, you can get the right product, with little or no waste of resources. 
    682 Posted by preform nicole
  • Your choice of china pet preform manufacturers will determine your success or failure. Speaking of your product, there should be no omissions. You need to ensure the quality of each step. Choosing the right manufacturer of custom plastic parts is the only way.Here are a few questions you should ask when choosing a suitable plastic parts manufacturer:Are their quality management system certified?The manufacturer's quality management system (QMS) determines their output. Certain industry standards should be adhered to to meet each product requirement. Make sure they pass the ISO certification. In addition, ensure that the certifying party is recognized and impartial.Is there enough support for new product development?A competent engineering support team can ensure the efficiency of each step. It is this team that can help Pet Bottle Mould balance design and manufacturing optimization. In this way, you can get the right product, with little or no waste of resources. 
    Sep 28, 2018 682
  • 27 Sep 2018
    When looking for a reliable china pet preform manufacturers, if you feel that the Internet search is too much trouble, too much effort, try to use the recommendations around you. Some of the best clues can come from recommendations from friends and family. Social networks make the word easier to say, so be sure to use these channels. When you start exploring, even if they may not be what you want, remember to ask if they can lead you in the right direction. They are very likely to have good connections in this industry, and many people will be happy to recommend you to more suitable people.Trade Show - Trade Show is another way to find legitimate suppliers. By participating in trade shows, you have the opportunity to meet face-to-face with potential suppliers. Therefore, you know more about their company, products, production capabilities, quality control procedures and other key business areas. This direct interaction can help you evaluate suppliers and verify their capabilities.If you decide to participate in China's trade show, the Canton Fair is the last show you want to miss. Canton Fair, China Import and Export Fair, is a trade fair designed to connect Chinese manufacturers and wholesalers with buyers and exporters. It has been in operation since 1957 and held its 120th session in October 2016. You can apply to visit the Canton Fair here. Although the approval process is usually very fast, prepare enough time for your application before you travel. Advance applications are usually free, but tickets for the day are not.Verify product qualityVisiting your supplier's production site in China is the only reliable way to truly understand its capabilities. This will help you understand the factories where Chinese manufacturers may be producing your products, and other information can be collected from there. You can have the opportunity to meet key players in China who may be producing your product. Last but not least, it lets your ultimate Chinese supplier know that you take your products very seriously and visit them in person to make sure they are made correctly. A face-to-face meeting with the supplier management team will also give you an idea of ​​their rapid processing experience and willingness to start the project.At first, the research process can be stressful, frustrating, time consuming, and nerve-racking. However, as time goes on, it becomes easier and less annoying. When your Pet Bottle Mould product reaches its final destination, is packaged and ready to go on the market, there is no better return.
    579 Posted by preform nicole
  • When looking for a reliable china pet preform manufacturers, if you feel that the Internet search is too much trouble, too much effort, try to use the recommendations around you. Some of the best clues can come from recommendations from friends and family. Social networks make the word easier to say, so be sure to use these channels. When you start exploring, even if they may not be what you want, remember to ask if they can lead you in the right direction. They are very likely to have good connections in this industry, and many people will be happy to recommend you to more suitable people.Trade Show - Trade Show is another way to find legitimate suppliers. By participating in trade shows, you have the opportunity to meet face-to-face with potential suppliers. Therefore, you know more about their company, products, production capabilities, quality control procedures and other key business areas. This direct interaction can help you evaluate suppliers and verify their capabilities.If you decide to participate in China's trade show, the Canton Fair is the last show you want to miss. Canton Fair, China Import and Export Fair, is a trade fair designed to connect Chinese manufacturers and wholesalers with buyers and exporters. It has been in operation since 1957 and held its 120th session in October 2016. You can apply to visit the Canton Fair here. Although the approval process is usually very fast, prepare enough time for your application before you travel. Advance applications are usually free, but tickets for the day are not.Verify product qualityVisiting your supplier's production site in China is the only reliable way to truly understand its capabilities. This will help you understand the factories where Chinese manufacturers may be producing your products, and other information can be collected from there. You can have the opportunity to meet key players in China who may be producing your product. Last but not least, it lets your ultimate Chinese supplier know that you take your products very seriously and visit them in person to make sure they are made correctly. A face-to-face meeting with the supplier management team will also give you an idea of ​​their rapid processing experience and willingness to start the project.At first, the research process can be stressful, frustrating, time consuming, and nerve-racking. However, as time goes on, it becomes easier and less annoying. When your Pet Bottle Mould product reaches its final destination, is packaged and ready to go on the market, there is no better return.
    Sep 27, 2018 579
  • 26 Sep 2018
    Jilian Plastic Mould is a china pet preform manufacturers. In addition to serving Chinese customers, our customers are all over the world. Jilian Plastics provides reliable, high quality custom plastic extrusion products.Our core competency is custom extrusion services.24-hour online extrusion operationThe outer diameter of the pipe is up to 3 inches, and the extrusion line of the profile is up to 6 inches.Various extruded plastic materialsProfessional plastic extruderJilian Plastics produces flexible and rigid plastic extruded pipes and plastic profiles for different industries. Our resources include a large number of thermoplastic compounds that meet the requirements of the Food and Drug Administration (FDA) and the National Sanitation Foundation (NSF). These standards are critical to the food and beverage processing industry.Why choose Jilian mold to meet the extrusion needs:Minimize processing costsUse custom polymersRapid sample processingISO 9001: 2008 certified quality management systemThrough on-time delivery, lean production,Blanket order and kanban systemInternal processingCustom color matchingExcellent customer service and innovationYour Pet Bottle Mould project will have the perfect color, with Universal's custom color and color matching capabilities, including phosphors. Our process provides high-transparency, transparency, high gloss and/or matte plastic extrusion products.Our experienced and knowledgeable engineering and production teams will provide high performance, engineered and commercial thermoplastics to help you with your specific applications and requirements involving plastic materials.
    615 Posted by preform nicole
  • Jilian Plastic Mould is a china pet preform manufacturers. In addition to serving Chinese customers, our customers are all over the world. Jilian Plastics provides reliable, high quality custom plastic extrusion products.Our core competency is custom extrusion services.24-hour online extrusion operationThe outer diameter of the pipe is up to 3 inches, and the extrusion line of the profile is up to 6 inches.Various extruded plastic materialsProfessional plastic extruderJilian Plastics produces flexible and rigid plastic extruded pipes and plastic profiles for different industries. Our resources include a large number of thermoplastic compounds that meet the requirements of the Food and Drug Administration (FDA) and the National Sanitation Foundation (NSF). These standards are critical to the food and beverage processing industry.Why choose Jilian mold to meet the extrusion needs:Minimize processing costsUse custom polymersRapid sample processingISO 9001: 2008 certified quality management systemThrough on-time delivery, lean production,Blanket order and kanban systemInternal processingCustom color matchingExcellent customer service and innovationYour Pet Bottle Mould project will have the perfect color, with Universal's custom color and color matching capabilities, including phosphors. Our process provides high-transparency, transparency, high gloss and/or matte plastic extrusion products.Our experienced and knowledgeable engineering and production teams will provide high performance, engineered and commercial thermoplastics to help you with your specific applications and requirements involving plastic materials.
    Sep 26, 2018 615
  • 25 Sep 2018
    The surface finish always has an impact on the appearance, function and feel of the Pet Bottle Mould, which is the key to designing a successful product. Knowing how to choose the best topcoat is a matter of designing the product. Here are some of our ideas and tips for your reference.Rapid manufacturing, surface treatmentWhat is this product for?Parts used in different environments are subject to UV light, heat, vibration, moisture... Careful consideration of how the part works and which surfaces are exposed, over time, the exposed surface may wear and tear, appropriate The surface finish protects the part from these problems.Who is the product for?To ensure the best user experience, choosing a surface finish based on customer preferences is an important aspect.Jilian Plastic Mould is an extremely professional china pet preform manufacturers. It has a wealth of experience in the surface finish of the products. The molds we produce are exquisite in appearance and more practical. They are the choices that customers should not miss. 
    615 Posted by preform nicole
  • The surface finish always has an impact on the appearance, function and feel of the Pet Bottle Mould, which is the key to designing a successful product. Knowing how to choose the best topcoat is a matter of designing the product. Here are some of our ideas and tips for your reference.Rapid manufacturing, surface treatmentWhat is this product for?Parts used in different environments are subject to UV light, heat, vibration, moisture... Careful consideration of how the part works and which surfaces are exposed, over time, the exposed surface may wear and tear, appropriate The surface finish protects the part from these problems.Who is the product for?To ensure the best user experience, choosing a surface finish based on customer preferences is an important aspect.Jilian Plastic Mould is an extremely professional china pet preform manufacturers. It has a wealth of experience in the surface finish of the products. The molds we produce are exquisite in appearance and more practical. They are the choices that customers should not miss. 
    Sep 25, 2018 615
  • 24 Sep 2018
    Injection molding has become an integral part of the manufacturing industry. Parts that have been manufactured using this technology have evolved over the years. What are the daily items made using injection molding?Here are some more products made using the injection molding process for everyday life:Cooking utensils: Various types of cooking utensils, such as plates, bowls and cups, are made of plastic material. Pet Bottle Mould injection molding technology is used to make these products in a variety of shapes.Children's toys: This is one of the most common applications for injection molding. Every family has some children's toys, and almost all children's toys are made of plastic materials. This is because this material provides good strength to the toy, thus making them durable. In addition, the toy can be cleaned to keep it clean and free of dirt. These toys are now available in different shapes and sizes and are therefore injection molded.Medical tools: The medical industry is another area where plastic injection molded parts are widely used. Many manufacturing methods and devices have been made using this manufacturing method to help achieve accuracy. Products such as syringes are manufactured using this technology and are therefore very effective and safe to use.CDs & DVDs: You will be surprised to find that CDs and DVDs are also injection molded. This is not all. The plastic boxes you use to save these discs and protect them from damage are also plastic molded products.Cover: A lid or lid used to close a container. The bottle is also an injection molded product. Covers of different shapes and sizes can be easily and efficiently manufactured by this technique.The list can go on. However, the injection molding products mentioned in this and previous articles are products that are used on a large scale every day in a wide range of applications. You can also custom design and mold these products to meet your application needs. There are many manufacturers in the United States that can help you meet the requirements of plastic molded products. However, only a few are reliable and have the expertise to manufacture high quality and precision parts. Jilian Plastics is one of the few experienced and trusted china pet preform manufacturers and has been providing custom injection molding services and precision parts for many years.
    627 Posted by preform nicole
  • Injection molding has become an integral part of the manufacturing industry. Parts that have been manufactured using this technology have evolved over the years. What are the daily items made using injection molding?Here are some more products made using the injection molding process for everyday life:Cooking utensils: Various types of cooking utensils, such as plates, bowls and cups, are made of plastic material. Pet Bottle Mould injection molding technology is used to make these products in a variety of shapes.Children's toys: This is one of the most common applications for injection molding. Every family has some children's toys, and almost all children's toys are made of plastic materials. This is because this material provides good strength to the toy, thus making them durable. In addition, the toy can be cleaned to keep it clean and free of dirt. These toys are now available in different shapes and sizes and are therefore injection molded.Medical tools: The medical industry is another area where plastic injection molded parts are widely used. Many manufacturing methods and devices have been made using this manufacturing method to help achieve accuracy. Products such as syringes are manufactured using this technology and are therefore very effective and safe to use.CDs & DVDs: You will be surprised to find that CDs and DVDs are also injection molded. This is not all. The plastic boxes you use to save these discs and protect them from damage are also plastic molded products.Cover: A lid or lid used to close a container. The bottle is also an injection molded product. Covers of different shapes and sizes can be easily and efficiently manufactured by this technique.The list can go on. However, the injection molding products mentioned in this and previous articles are products that are used on a large scale every day in a wide range of applications. You can also custom design and mold these products to meet your application needs. There are many manufacturers in the United States that can help you meet the requirements of plastic molded products. However, only a few are reliable and have the expertise to manufacture high quality and precision parts. Jilian Plastics is one of the few experienced and trusted china pet preform manufacturers and has been providing custom injection molding services and precision parts for many years.
    Sep 24, 2018 627

Most Viewed Blogs/Articles From This Author

  • 10 Oct 2018
    Injection Molding Plastics Since the introduction of the injection molding process for the first time in the 1930s, the advantages of injection molding over die casting have been controversial. This approach has both benefits and limitations, mainly based on requirements. pet preform manufacturers and other consumers who rely on molded parts to produce products are looking for factors such as quality, durability and economy to determine which molded parts are best suited to their needs.What is injection molding?Injection molding is a method of manufacturing a finished part or product by pressing a molten plastic into a mold and hardening it. The use of these components is as extensive as the various products produced by the process. Depending on the application, injection molded parts can range in weight from a few ounces to hundreds or thousands of pounds. In other words, from computer parts, soda bottles and toys to trucks, tractors and car parts.Injection drawingPlastic injection molding and die castingThe injection molding process was originally modeled by die casting, a similar process in which molten metal is pressed into a mold to produce parts for making the product. However, die casting mainly uses non-ferrous metals such as zinc, aluminum, magnesium and brass instead of using plastic resins to produce parts. Although almost any part can be cast from any metal, aluminum has developed into one of the most popular metals. It has a low melting point which makes it easy to form parts. The mold is stronger than the mold used in the permanent mold process and can withstand high pressure injections of 30,000 psi or higher. The high pressure process produces a durable, fine grade structure with fatigue strength. Because of this, die casting is used from engine and engine parts to pots and pans.Die casting benefitIf your company needs rugged, durable, mass-produced metal parts such as junction boxes, pistons, cylinder heads and engine blocks, or propellers, gears, bushings, pumps and valves, die casting is the ideal choice.StronglastingEasy to mass produceDie casting limitHowever, it can be said that although die casting has its advantages, there are some limitations in this method that need to be considered.Limited part sizes (up to approximately 24 inches and 75 pounds.)High initial processing costMetal prices will fluctuate significantlyWaste increases production costsInjection molding benefitsFor many years, the benefits of preform injection molding of Pet Bottle Preform have become more popular because of their advantages over traditional die-casting methods. That is to say, the number and variety of low-cost, inexpensive products made today from plastic are almost limitless. There are also minimum finishing requirements. 
    3778 Posted by preform nicole
  • 09 Oct 2018
    In the field of product development and manufacturing, 3D printing and injection molding are almost universally considered to be among the best available methods. While these methods are versatile and well suited for many situations and uses, they vary widely in several ways: method, material, volume, cost, and best application – just a 5-gallon Pet Preform example.confrontationAs an entrepreneur, new product developer or engineer, you probably know that 3D printing and injection molding are definitely two options you should research and pursue to create your product or prototype and understand some of the key differences between the two. Very important. First, they operate in a completely different way. Let us briefly outline what this means.Injection molding and 3D printing: What are they?Injection molding involves injecting a heated liquefied plastic material into a mold that contains a 3D "negative film" that can be thought of as your part: when the liquefied plastic fills the mold cavity, it forms and forms your part. . Once the mold cavity is filled, the substrate is allowed to cool and resolidify and then drained from the mold for inspection and dispensing.Injection molding machines cost hundreds of thousands of dollars to facilitate the entire cycle: material loading, injection, cooling and parts removal. Injection molds are almost always custom made of steel, aluminum or other metals to fit the specifications of a particular part, and they are split into two halves so they can be pushed out separately. In addition to the cavity having the "negative" shape of the part, the mold also contains a hollow area called a "flow path" for conveying the molten material into the cavity.The 3D printing process works much differently than injection molding. The size, shape, and other physical characteristics of the product are loaded into the 3D printer through CAD drawings or other compatible files, rather than forming the part through a preformed mold. The machine then builds parts from the ground and processes the thin lines of plastic substrates that are transported through the machine.If you don't know how to choose the right craftsmanship for your mold, please contact Jilian Plastics. We are a well-experienced china pet preform manufacturers that can find the right method for you.
    1251 Posted by preform nicole
  • 07 Oct 2018
    The Pet Bottle Mould blowing machine is a kind of mechanical, electronic control, hydraulic integrated crystallization, electrical complexity, oil pipeline crossing the building, various fault phenomena are controllers, all kinds of strange things, different. Large PET bottle blowing machines have only tens of thousands of parts. If one of the parts fails, the PET bottle blowing machine will be abnormal, and the wire connection will cause problems if it is slightly inadvertent, plus the blower is bulky. PET, without the impact of a constant temperature blow molding machine on the shop environment, can easily lead to failure. To this end, the maintenance problems of imported PET blow molding machines are in front of us.How to quickly identify faults, hidden dangers and timely elimination? I think we should have a high sense of responsibility. Secondly, we should try our best to master the numerical control hydraulic technology. The practice of maintaining the blow molding machine for many years makes the PET more and more want to look more and more, and the more we want to practice, gradually improve our technical level and maintenance ability. , able to adapt to a variety of complex situations, solve difficult problems, PET bottle blowing machine.1View more PET blower electronic circuit informationWant to know more, understand the characteristics and functions of various PET blow molding machines, electronic circuit systems and PC PLC PLC; understand the electronic alarm system and troubleshooting of PET blow molding machine; understand the meaning of setting parameters of PC and PLCPET blow molding machine; Understand the programming language of PC and PLC; understand the method of programming PET blow molding machine; to understand the operation of the control panel PET blow molding machine and the contents of the menu, how long does it take to have a lot of data? I think the main focus, to clarify the sequence of events, is to master the spirit of the PET blow molding machine controller structure and control block diagram. The rest can be "visiting" and reading, but the content of each part must emphasize understanding and mastery. Because the internal circuit diagram of the PET blower controller is quite complicated, the manufacturer does not provide it. So you don't have to think about it in detail. Pay attention to the role of each part, the function of the board, the position of the interface, the meaning of the LED light, etc.. Now the model of the PET blow molding machine is updated fast, different manufacturers and different models are often different. Understand its commonality and personality.2View more PET blow molding machine electrical diagram, digest PET blower electrical diagramFor each electrical component, such as contactors, relays, time relays, and PC, PLC inputs, outputs, be marked on the electrical diagram.3. View more PET blow molding machine hydraulic drawings and digest them deeplyFor PET blow molding machines, hydraulic diagrams to understand their function and sequence of events. And one by one on the drawing, such as the lock mode is made by which solenoid valve action? Corresponding to PC, PLC output, what are the inputs? As shown in the figure, so from the electromechanical action to the extreme, at the same time, especially for the motor, more closely related to the understanding, now PET blow molding machine using electro-hydraulic proportional technology, should pay attention to understanding the role and function, especially understanding Adjustment methods and adjustment data, current pressure proportional valve pumps and corresponding static and dynamic, can understand and understand the motor, mechatronics, master various skills, such as the ability to solve problems.china pet preform manufacturers have a wealth of experience in pet blow molding machines, can quickly help you identify machine failures, eliminate problems, ensure that you smoothly produce products, and minimize losses.
    773 Posted by preform nicole
  • 13 Sep 2018
    The growing demand for sustainable development by the environment and consumers is a hot topic of np2o 2018 this year. When it comes to sustainability, there are very few processes that rival those of China's injection molded Pet Bottle Mould – a fact that can lower your costs while giving your customers peace of mind.Let's take a look at how sustainability fits into injection molding and what to watch out for in the manufacturer to ensure you work with sustainable companies.Sunrise sustainable manufacturing wasteWhen it comes to plastic mold injection molding, very few processes can improve the efficiency of materials. Expect a manufacturer to combine selective automation with state-of-the-art injection molding machines to ensure the highest quality products. High quality products not only mean better consistency, but also mean overall waste reduction.Injection molding is a low-wasting process, but where there is waste – in extreme forming, we like to use hot runners and cold runner technology to reduce waste.When you find a manufacturer with a history of precision engineering in areas such as medical parts and baby products, you can rest assured that they will be able to minimize the waste of resins and plastics because they will produce consistently superior products.Made in ChinaRepositioning your manufacturing industry is an easy way to focus on sustainable manufacturing. If your product is much shorter than the consumer – in fact, if your manufacturer can also do secondary processing at home – then the products you produce are more environmentally friendly.Finding local manufacturers in China is a good way to show your customers that you are committed to sustainable plastics manufacturing. The side effect of finding a Chinese plastics manufacturer is that they will also improve the quality of your products and can communicate face to face with you. Having a manufacturer you can understand is how you develop lasting and solid relationships that lead to future collaboration and innovation.In extreme styling, we like to exceed expectations in customer service. We believe that the key to any relationship – and to increase your sustainability – lies in our close working relationship with our partners.In terms of injection molding, we continue to expand our boundaries and explore new possibilities for our partners. For more than 15 years, we have always ensured that our partners' priorities are our priorities, and we believe that when you are looking for a china pet preform manufacturers that can help you meet consumer needs, this will have different. If you have a baby product that you want to produce, contact us today for a free consultation. We are happy to sign Non-Disclosure Agreements (NDAs) to ensure that you retain intellectual property.
    733 Posted by preform nicole

Categories This Author Writes About

View all blogs from everyone